Home

/

/

Bright Steel Bar

Bundle of bright steel bars strapped on a rack

Bright Steel Bar

Cold drawn, peeled and ground bright bars in round, square, flat and hex sections. We saw cut, turn and machine bars on our in-house processing lines, so they arrive ready for your machines.

Cold drawn bar to ISO h9, h10, h11 or h12

Round Ø3–120 mm, square 3–150 mm, hex 4.5–90 mm A/F

Peeled round bar Ø16–300 mm; precision ground bar Ø5–200 mm to h6–h8

SAE 1018, 1020, 1045 and C45 regularly supplied

Why Buy Bright Bars From MTS


Cut, Chamfered and Machined

We saw cut bright bar to your length, then chamfer and face the ends square. Our CNC lathe and four machining centers turn parts up to Ø500 mm to ±0.02 mm.

Drawn, Peeled or Ground

Cold drawn bar covers small and mid sizes. Peeled bar takes over up to Ø300 mm. Ground bar gives the closest tolerance and finest surface. You pick the route by size and tolerance.

Tolerance Matched to Your Use

We supply cold drawn bar in ISO h9 to h12. You pay for the tolerance your part needs, not the tightest one available.

Bright Bar From Our Stock

Bright bar is part of our 6,000 tons of carbon steel bar stock. Stock changes constantly, so contact us to confirm current sizes and grades.

Heat Treatment Arranged

We can supply 1045 and C45 bright bar quenched and tempered. We also arrange induction hardening for shafts and guide rods.

Bright steel bars packed in wooden cases for export

Bright Bar That Goes Straight Into the Machine

A bright bar is ready to use as delivered. The surface is clean, the size is held to an h-class and the bar is straight.

That changes how you machine. Bright bar runs through bar feeders and collets with no roughing pass. Many pins, spacers and shafts use the bar diameter as it is. You skip a whole operation compared with black bar.

Send us the finished part size and tolerance. We’ll advise on drawn, peeled or ground bar, plus the class that fits.

Request a Quote

Bright Steel Bar by Process


Cold drawn bright steel bars stacked on the floor

Cold Drawn Bar

Hot rolled bar pickled and drawn cold through a die. Drawn bar is smooth, straight and held to h9–h12. We also cold draw special sections to your drawing.

Peeled steel round bars with turned surface

Peeled Bar

Hot rolled bar turned on a peeling machine to remove scale and surface defects. Peeled bars run up to Ø300 mm, larger than cold drawing can reach.

Precision ground steel bars in a wooden case

Precision Ground Bar

Precision ground round bar to ISO h6, h7 or h8, plus turned, ground and polished (TG&P) bar. Ground flat stock suits jigs, gauges and tool parts. Sizes are in Tab 1.

Bundle of hardened steel rods tied for shipment

Hardened Steel Rod

Induction hardened and ground bar, without chrome, for linear shafts, guide rods and smooth rods. We supply C45 / C45E, 1045, S45C, C55E and Cf53, with alloy grades such as 41Cr4 and 42CrMo4 on order. Hardness, case depth and tolerance follow your drawing.

Chrome plated steel rods with a mirror finish

Chrome Plated Rod

Ground and hard chrome plated bar for hydraulic cylinders.

Bright Steel Bar by Grade


1018 Cold Rolled Steel

SAE 1018 is the most common bright bar grade. Cold rolled steel 1018 to ASTM A108 machines and welds well, for pins, studs and spacers.

SAE 1020

Low carbon bright bar, similar to 1018, for general turned parts.

1045 and C45 Bright Bar

Medium carbon bright bar for shafts and gears, supplied as drawn or quenched and tempered.

Free-Machining Bright Bar

12L14, 1215, 11SMn30 and 11SMnPb30 bright bar for automatic lathes. Other free-machining grades on request.

Example: SAE 1018 cold drawn round bar, Ø25 mm h10, 3,000 mm lengths.

Bright Steel Bar Specifications


ProcessRoundSquareHexLength
Cold drawnØ3–120 mm3–150 mm4.5–90 mm A/F2,000–6,000 mm
PeeledØ16–300 mm––2,000–6,000 mm
Precision groundØ10–100 mm common; Ø5–200 mm (some sizes to Ø250 mm)––To order
TG&PØ20–100 mm common; Ø12–200 mm––To order
Ground flat stock5–30 × 20–100 mm common; 3–50 × 10–200 mmTo order

Cold drawn flats run 2–40 mm thick × 8–140 mm wide. Sizes outside these ranges need confirmation with us.

How to Buy Bright Steel Bar

What Is a Bright Bar?

Bright bar is steel bar with a clean, bright surface and a close tolerance. Mills make it by cold drawing, peeling or grinding hot rolled bar. Cold rolled steel rod and cold finished bar are other names buyers use for the same product.

Cold Drawn or Peeled?

Cold drawing squeezes the bar through a die. It work-hardens the surface, raises strength a little and gives good straightness. It suits small and mid sizes.

Peeling turns off the outer skin instead. It removes surface seams and decarburization completely, which matters for induction hardened parts. Choose peeled bar for large diameters and for parts where surface soundness matters most.

Choosing the Tolerance Class

  • h9: precision pins and shafts used at drawn size
  • h10–h11: general bright bar for bar feeders and collets
  • h12: bar that will be skimmed after cutting

For tighter fits than h9, choose precision ground bar in h6–h8. Asking for h9 on a part you will turn anyway only adds cost.

Bright Bar Sizes

Common sizes include 8 mm, 10 mm, 12 mm, 16 mm, 25 mm, 30 mm and 40 mm bright bar. In inches, 1/2, 5/8, 3/4 and 1 inch cold rolled steel rod are frequent requests. Send inch sizes. Where we can, we cold draw or grind to the exact inch size. If not, we recommend the nearest metric size for your approval.

Bright Bar Properties

Cold drawing raises tensile strength and hardness slightly compared with the same grade hot rolled. Machinability also improves, because the surface is clean and the size is consistent. The mill test certificate shows the actual properties for each heat.

Precision Ground and Smooth Rods

Linear motion parts need more than a drawn surface. An 8 mm smooth rod or linear rod for a 3D printer or slide is usually induction hardened and ground. We supply hardened steel rod in C45, 1045 and similar grades to your hardness and tolerance.

Choosing a Bright Bar Supplier

Ask each bright bar supplier the same questions. Which tolerance class? Which grade and standard? Peeled or drawn at large sizes? Is cutting included? Comparing price per ton without these answers compares different products.

Frequently Asked Questions


What is the difference between bright bar and black bar?

Black bar is hot rolled, with mill scale and a wider tolerance. Bright bar is cold drawn, peeled or ground, with a clean surface and an h-class tolerance. Bright bar costs more but needs less machining.

What is peeled bar?

Peeled bar is hot rolled bar turned to remove the scale and outer skin. It has a bright surface and no surface seams. We supply peeled bar Ø16–300 mm.

Is 1018 cold rolled steel the same as cold drawn?

Yes, in bar form. "Cold rolled steel 1018" usually means 1018 cold drawn bar to ASTM A108. It is the most common low carbon bright bar grade.

What is TG&P bar?

TG&P means turned, ground and polished. We turn or peel the bar, then centreless grind and polish it for a close tolerance and smooth finish. It suits shafts and precision parts.

Is bright bar in stock?

We hold common sizes and grades of bright bar in stock. Stock changes constantly, so please check current availability with us.

Related Products


More in This Category


Request a Quote


We reply within 2–4 working hours with a price per ton, valid for 3 days.

Scroll to Top

Envíe su consulta hoy

Envíenos el grado, la medida, la cantidad y el puerto de destino que necesita. Para productos estándar, le enviamos una cotización en 2–4 horas hábiles.

Send Your Inquiry Today

Send us your required grade, size, quantity and destination port. For standard products, we will provide a quote within 2–4 working hours.