Home

/

/

Carbon Steel Round Bar

Carbon steel round bars in stock

Carbon Steel Round Bar

Hot rolled, cold drawn and peeled steel round bar, saw cut to the length your machines need. We cut, chamfer and turn rounds on our in-house processing lines, then ship them from our own warehouses.

Standard diameters Ø12–100 mm; hot rolled Ø6–400 mm

Cold drawn Ø3–120 mm to ISO h9–h12; peeled Ø16–300 mm

SAE 1018, 1020, 1045, C45, S235JR and S355JR regularly supplied

Saw cut to fixed length; quotations in 2–4 working hours

Why Buy Steel Round Bar From MTS


Saw Cut and Turned to Your Drawing

We saw cut round bars to fixed lengths, then chamfer and face the ends. We also turn and machine parts up to Ø500 mm, to ±0.02 mm.

Three Finishes Across a Wide Diameter Range

You can match the finish to each diameter on one order:

• Hot rolled: Ø6–400 mm
• Cold drawn: Ø3–120 mm
• Peeled: Ø16–300 mm
• Precision ground: Ø5–200 mm

Common Diameters From Bar Stock

Our 6,000 tons of carbon steel bar stock includes round bar in common diameters. Stock moves quickly, so contact us to confirm current sizes and grades.

Heat Treated to Your Requirement

We supply 1045 and C45 rounds annealed, normalized or quenched and tempered, and can induction harden them. For low carbon 1018 and 1020 pins, we arrange carburizing.

Certified and Shipped From Three Ports

Every order comes with a mill test certificate. Rounds ship from Shanghai, Qingdao or Tianjin, and we photograph each container before it is sealed.

Carbon steel round bars in stock

The Right Round Stock Saves Machining Time

Round bar is the starting point for most turned parts. A shaft, pin or bolt starts as a length of round stock steel. The lathe removes everything that is not the part.

So the diameter you buy matters. Buy too large and you turn away steel you paid for. Buy too close and scale or a surface seam can stay in the finished part. The right size depends on the finish, as the table below shows.

Send us your finished diameter and length. We’ll suggest the bar size, finish and cut length that waste least.

Request a Quote

Steel Round Bar by Finish


Carbon steel round bars in stock

Hot Rolled Steel Round Bar

Black round bar with mill scale, to EN 10060 tolerances. The low-cost choice for forging billets, parts machined all over and fabrication.

Cold drawn steel round bars strapped in bundles

Cold Drawn Round Bar

Round bright bar drawn to ISO h9–h12. It is straight and clean, so it runs on bar feeders with little stock removal.

Carbon steel round bars in stock

Peeled Round Bar

Hot rolled bar turned to remove scale and surface defects. Peeled bar gives a bright, sound surface in sizes too large to draw.

Precision ground steel round bars cut to length

Ground Round Bar

Precision ground round bar to ISO h6, h7 or h8, and turned, ground and polished (TG&P) bar. For bearing fits, guide pins and shafts.

Steel Round Bar by Grade


Mild Steel Round Bar

SAE 1018, 1020 and S235JR. Plain round bar that welds, bends and machines easily, for pins, studs, frames and general parts.

1045 and C45 Round Bar

Medium carbon round bar for shafts, axles, gears and hydraulic parts. We supply it hot rolled, normalized or quenched and tempered.

Structural Round Bar

We regularly supply S355JR, with S355J2, ASTM A36 and A572 Gr. 50 on request. For tie rods, anchor bolts and welded structures.

Free-Machining Round Bar

SAE 12L14, 1215, 11SMn30 and 11SMnPb30 rounds for automatic lathes and high-volume turned parts. We supply 1117, 1144 and EN1A on request.

Alloy Steel Round Bar

4140, 42CrMo4, 4340 and 4130 rounds for high-strength shafts and heavy-duty parts.

Steel Round Bar Specifications


FinishDiameterToleranceLength
Hot rolledØ12–100 mm standard; Ø6–400 mmEN 100603,000 / 6,000 / 9,000 / 12,000 mm
Cold drawnØ3–120 mmISO h9, h10, h11, h12 (EN 10278)2,000–6,000 mm
PeeledØ16–300 mmTo process and your requirement2,000–6,000 mm
Precision groundØ10–100 mm standard; Ø5–200 mm (some sizes to Ø250 mm)ISO h6, h7, h8 (ISO 286)To order
TG&PØ20–100 mm standard; Ø12–200 mmTo your drawingTo order

Sizes outside these ranges need confirmation with us, and some are made to order. We saw cut any bar to a fixed length, and confirm special lengths per order.

How to Choose Steel Round Bar

Hot Rolled, Cold Drawn or Peeled?

Choose by how much you will turn off. Hot rolled round bars carry scale and a thin decarburized skin. Plan to remove that skin all round, so buy a size up. For parts turned all over, this is still the cheapest start.

Cold drawn bar is close to size, straight and bright. If your part uses the bar diameter as it is, or skims only a little, cold drawn saves a lathe operation. Peeled bar suits large diameters. It also suits parts where surface seams must be gone before heat treatment.

The usual overspend we see is cold drawn bar bought for a part that is turned all over anyway.

Choosing a Tolerance Class

Cold drawn round bar comes in ISO h9 to h12. A tighter class costs more. Match it to how you hold and use the bar:

  • h9: bar used at drawn size for precision pins and shafts
  • h10–h11: general bright bar on bar feeders and collets
  • h12: parts that will be skimmed or turned afterwards

If you are unsure, send the finished part tolerance, and we’ll suggest a class.

Plain Round Bar or Rebar?

Plain round bar has a smooth surface for machining and fabrication. Rebar has ribs to grip concrete and follows construction standards. Smooth bar is also called plain rod. Check which one your project needs before you order.

Steel Round Bar Sizes in mm and Inches

Round bar sizes are metric. Small sizes such as 6 mm, 8 mm and 10 mm round bar are usually cold drawn. Mid sizes such as 12 mm, 16 mm, 20 mm, 25 mm and 30 mm come hot rolled or drawn.

For inch sizes such as 1/4, 3/8, 1/2, 5/8 or 1-1/2 inch round stock, send the size. Where we can, we cold draw or grind the bar to the exact inch size. If not, we recommend the closest metric size for your approval.

Calculating Round Bar Weight

Steel round bar weight per meter is easy to estimate:

Weight (kg/m) = diameter (mm) × diameter (mm) × 0.00617

For example, a Ø50 mm bar weighs about 15.4 kg/m, and a 6 m bar about 92.5 kg. Use this to check freight, bundle size and the lifting gear you need.

Straightness and Cutting

Hot rolled rounds are straight enough for most fabrication. Cold drawn and peeled bars are straighter, which matters on bar feeders. If you need straightness better than standard, state it on your enquiry.

Saw cut pieces arrive with flat ends. Chamfered ends load into machines more easily and are safer to handle.

Frequently Asked Questions


What sizes of steel round bar do you supply?

Standard diameters run from Ø12 to Ø100 mm. Hot rolled round bar goes from Ø6 to Ø400 mm, and cold drawn from Ø3 to Ø120 mm. Peeled bar covers Ø16–300 mm. We confirm other sizes per order.

What is round bright bar?

Round bright bar is cold drawn round bar with a clean, bright surface. We hold it to ISO h9–h12, and it is straighter than hot rolled bar. It suits bar feeders and parts used at, or close to, the bar diameter.

Is carbon steel round bar in stock?

We hold common diameters and grades of carbon steel round bar in stock. Stock changes constantly, so please check current availability with us before you order.

Can you cut round bar into short pieces?

Yes. We saw cut round bar to any fixed length, and chamfer or face the ends. Send the piece length, tolerance and quantity. We can also turn or mill blanks to your drawing.

What is the difference between solid round bar and round tube?

Solid round bar is steel all the way through. It carries more load for its diameter and is machined into shafts, pins and fittings. Round tube is hollow, lighter and used where weight matters more than strength.

How do I calculate steel round bar weight?

Multiply the diameter in millimeters by itself, then by 0.00617. The answer is kilograms per meter. A Ø20 mm bar weighs about 2.47 kg/m.

More in This Category


Request a Quote


We reply within 2–4 working hours with a price per ton, valid for 3 days.

Scroll to Top

Envíe su consulta hoy

Envíenos el grado, la medida, la cantidad y el puerto de destino que necesita. Para productos estándar, le enviamos una cotización en 2–4 horas hábiles.

Send Your Inquiry Today

Send us your required grade, size, quantity and destination port. For standard products, we will provide a quote within 2–4 working hours.