
Cold Rolled Coil (CRC)
Cold rolled steel coil in commercial and drawing grades, from 0.3 mm to 3 mm thick. We slit, cut to length and rewind CR coil on our in-house processing lines, then ship it from our own warehouses.
Standard 0.3–3 mm thick and 1000–1500 mm wide; 0.2–4 mm and 700–1850 mm on request
Annealed (CRCA) for forming, or full hard (CRFH)
Matte and oiled as standard; bright finish on request for many grades
Mill test certificate with every coil; quotations in 2–4 working hours
Why Buy Cold Rolled Coil From MTS
Strip and Sheets Ready for Your Press
You get strip at the exact width your press or roll former runs, with no second processor in between. We slit CR coil into strips from 20 mm wide, with a width tolerance of ±0.2 mm. For sheets, we cut 300–2000 mm wide, flat to 5–7 mm per meter.
Coil Weight and ID for Your Decoiler
Standard cold rolled coils weigh 5–10 tons on a 508 mm ID, with 610 mm also available. On request, we supply coils from 3 to 15 tons. If your crane or decoiler needs smaller coils, we rewind thin gauges to suit.
Stock for the Gauges You Use Most
We keep 9,000 tons of carbon steel coil in our own warehouses, including cold rolled coil in common grades and widths. Between 1.5 mm and 2.0 mm, cold rolled, hot rolled and pickled coil are all in stock. You can compare the three on one quotation.
Annealed or Full Hard: Pick What Your Part Needs
Annealed coil bends and draws without cracking. Full hard coil is stiff and springy. It suits flat parts and is the base coil for galvanizing. Not sure which one? Describe the forming step and we'll advise.
Shipped From Three Ports
Processed CR coil ships in 8–12 working days from Shanghai, Qingdao or Tianjin. Every coil is wrapped against moisture, and every container is photographed before it is sealed.

Cold Rolled Steel Coil: Thinner, Flatter, Cleaner
Request a QuoteCold Rolled Coil by Condition

CRCA Coil (Cold Rolled, Close Annealed)
CRCA coil is annealed after cold rolling, which restores ductility. It is the standard choice for bending, stamping and deep drawing. CRCA is the name most used in India and the Middle East. In Europe and Japan, the grade name usually implies the annealed condition.

CRFH Coil (Cold Rolled Full Hard)
Full hard coil is not annealed after cold reduction. It is hard, strong and has little elongation. It is used for flat parts that are not formed. It is also the base coil for galvanizing and color coating lines.

Annealed Steel Coil With Skin Pass
Most annealed coil is skin passed (temper rolled) after annealing. A light skin pass sets the surface finish and flatness, and helps prevent stretcher strain marks during forming.
Cold Rolled Coil by Grade
SPCC and DC01 Commercial Quality
The everyday grades for bending, light pressing and welded parts. SPCC follows JIS G3141; DC01 follows EN 10130. ST12, the old DIN name, is still widely used for the same quality.
SPCD and DC03 Drawing Quality
For parts with deeper draws, such as housings, shells and brackets. Lower carbon and controlled properties give better formability than commercial quality.
DC04, ST14 and DC05 Deep Drawing Quality
For deep and complex automotive and appliance pressings. DC04, ST14 and DC05 are in stock. SPCE and DC06 are made to order.
Low Carbon Commercial Coil
A low-cost Chinese commercial grade for welded tube, light sections and general fabrication.
Example: DC04 cold rolled coil for appliance panels, 0.8 mm × 1250 mm, annealed, matte and oiled.
Cold Rolled Coil by Form
Master Coil
Full-width coil for service centers, galvanizing lines and high-volume press lines. Standard widths are 1000, 1250 and 1500 mm; 1250 mm is the most common.
Slit Coil
Narrow coils cut to your strip width, from 20 mm. For tube mills, roll formers and progressive dies.
Cut Sheets
CR sheets cut to length from coil, flattened and stacked. Usual lengths are 2000–6000 mm.
Cold Rolled Coil Specifications
How to Choose Cold Rolled Coil for Your Parts
Cold Rolled, Hot Rolled or Pickled?
Pick the Grade by the Depth of the Draw
Matte or Bright Finish
Oiled or Dry
Reading Cold Rolled Coil Prices
Storage on Arrival
Frequently Asked Questions
What is cold rolled coil?
Cold rolled coil (CRC) is steel coil that has been rolled again at room temperature after hot rolling and pickling. It is thinner, flatter and smoother than hot rolled coil, with tighter thickness tolerance. It is usually annealed for forming.
What is a CR coil?
CR coil is the short name for cold rolled coil. CR coil sheet and CR sheet coil mean the same product: cold rolled steel sheet wound into a coil.
What is the difference between CRCA and CRFH?
CRCA is cold rolled, close annealed coil, soft enough for bending and drawing. CRFH is cold rolled full hard coil, which is not annealed after rolling. It is hard and is used for flat parts or as base coil for coating lines. We supply both.
What grades of cold rolled steel coil do you supply?
We regularly supply SPCC, SPCD, DC01, DC03, DC04, DC05, ST12 and ST14. SPCE and DC06 are made to order.
What affects cold rolled coil steel prices?
The hot rolled market sets the base. Thickness, grade, annealed or full hard, width and processing add to it. For a current price per ton, send your specification and we will quote within 2–4 working hours.
What thickness of cold rolled coil can you supply?
Our standard range is 0.3–3.0 mm. We can supply 0.2–4.0 mm on request; sizes outside the standard range need confirmation and may be made to order.
Is SPCC coil the same as DC01?
They are close equivalents. SPCC is the JIS commercial grade and DC01 the EN commercial grade. Both are used for the same kind of parts. Their chemistry limits and test methods are not identical, so order to the standard your drawing states.
Related Products



More in This Category
Request a Quote
We reply within 2–4 working hours with a price per ton, valid for 3 days.
