Home

/

/

Hot Rolled Coil

Hot rolled steel coils stored outdoors beside a factory building

Hot Rolled Coil (HRC)

Hot rolled steel coils in structural, commercial and automotive grades, from 1.2 mm to 20 mm thick. We slit, level and rewind HR coil on our in-house processing lines, then ship it from our own warehouses.

Standard 1.2–20 mm thick and 1250–2000 mm wide; 0.8–25.4 mm and 800–2050 mm on request

Black or pickled and oiled surface; chequered pattern available

Slit, cut to length or rewound to your coil weight before shipping

Mill test certificate with every coil; quotations in 2–4 working hours

Why Buy Hot Rolled Coil From MTS


HR Coil Ready for Your Line

Most buyers don't run a full-width mill coil of up to 28 tons. Instead, you get coil slit to your width or sheets cut to your length, ready to load. We slit HR coils up to 14 mm thick into strips from 20 mm wide. For sheets, we cut up to 16 mm thick and 2000 mm wide.

Coil Weight and ID That Fit

Standard hot rolled coils weigh 15–25 tons, up to 28 tons, on a 760 mm ID. If your decoiler takes 610 mm, or your crane lifts less, we rewind to match. You pay for steel you can unload and run.

Stock for Common Grades and Sizes

Our 9,000 tons of carbon steel coil stock covers the common hot rolled grades and sizes. Most structural, pipe and fabrication orders ship without a mill wait. Less common grades are rolled to order.

Black or Pickled, From One Source

Between 1.2 mm and 8 mm, we offer both black and pickled and oiled coil. Between 1.5 mm and 2.0 mm, cold rolled is in stock too. You can compare surface and price on one quotation.

Shipped From Three Ports

Processed HR coil ships in 8–12 working days from Shanghai, Qingdao or Tianjin. Every container is photographed before it is sealed.

Hot rolled steel coils stacked in the warehouse

The Lowest-Cost Flat Steel, If You Buy the Right Coil

Hot rolled coil is rolled at high temperature, typically above 850 °C, and coiled while hot. This short route makes it the lowest-cost flat steel you can buy. The trade-off is a grey mill scale and wider gauge tolerance than cold rolled. For most structural, welded and painted parts, neither matters.

What matters is the match between coil and use. Choosing a grade too soft for the load can cost you later. So can mill scale on a paint line. So can a coil your crane can’t lift. A good HR coil order fixes those three points before the price is agreed.

Tell us what you make from hot rolled steel in coils, and which machine you run it on. We will recommend the grade and surface, and whether to buy master coil, slit coil or cut sheets.

Request a Quote

Hot Rolled Coil by Grade


SPHC hot rolled coils stacked in a workshop

SPHC Hot Rolled Coil (JIS G3131)

SPHC is the commercial grade of JIS G3131, used for bending, light stamping and welded tube. Standard 1.5–6.0 mm thick, with 1.2–12.0 mm available. Common widths are 1010, 1210, 1230, 1250, 1260 and 1500 mm. SPHD and SPHE are the drawing grades in the same standard.

Q235B and SS400 hot rolled coils on stock

SS400 Hot Rolled Coil

The most traded commercial-structural grade in Asia. SS400 (JIS G3101) suits frames, brackets, purlins and welded pipe. Example: SS400 mild steel hot rolled coil, 3.0 mm × 1500 mm.

ASTM A36 hot rolled coil with open eye

ASTM A36 Hot Rolled Coil

The American structural grade, specified across North and South America and the Middle East.

Q355B and S355JR hot rolled coils with strapping

EN S235JR / S275JR / S355JR

Structural grades for load-bearing parts, to EN 10025-2. Choose them when your drawing states a minimum yield strength.

Low carbon hot rolled coil for forming

Low Carbon Grades for Forming

SAE 1006 and SPHC give soft, ductile hot rolled carbon steel coil for tube making and deep forming.

Hot Rolled Coil by Surface


Black Hot Rolled Coil

As rolled, with mill scale. The usual choice for structural parts, pipe and parts that are blasted, galvanized or welded.

Pickled and Oiled Coil (HRPO)

HRPO stands for hot rolled, pickled and oiled. Acid pickling removes the scale, and a light oil film protects the clean surface in transit. Standard 1.5–6.0 mm thick and 1000, 1250 or 1500 mm wide.

Chequered Coil

Hot rolled coil with a raised pattern on one side. We supply diamond, lentil, round bean, teardrop and combination patterns. Standard 1.8–12 mm thick and 1250–1500 mm wide, in mild and structural grades. Cut into floor plate, stair treads and vehicle floors.

Automotive and High-Strength Hot Rolled Coil


Automotive Hot Rolled Coil: SAPH and QStE

We stock SAPH370 to SAPH440, QStE340TM to QStE420TM and truck frame steel for wheels, chassis members and frames. SAPH and QStE are mostly supplied as pickled coil.

MC High-Strength Steel Coil

Cold-forming high strength steel coil from S315MC to S700MC, and BS600MC to BS700MC. Standard 2.0–8.0 mm thick, for crane booms, trailer chassis and formed sections.

Hot Rolled Coil Specifications


ItemStandardAvailable on request
Thickness1.2–20 mm0.8–25.4 mm
Width1250 / 1500 / 1800 / 2000 mm800–2050 mm
Coil ID760 mm610 mm
Coil weight15–25 t10 t to max. 28 t
Coil ODabout 2000–2180 mmdepends on weight and width
EdgeMill edgeSlit edge

Sizes outside the standard column need confirmation with us. Coils over 20 mm are rare, heavy and made to order; they are supplied as full coils, without slitting or leveling.

How to Choose Hot Rolled Coil for Your Application

Start With the Load, Then the Grade

If the part carries no designed load, a commercial grade such as SPHC, SAE 1006 or SS400 is enough. It bends and welds easily, and it costs the least.

If your drawing states a yield strength, buy a structural grade to that standard. S235JR gives 235 MPa minimum yield and A36 250 MPa; S355JR gives 355 MPa. Grades across standards are close, not identical. Check the chemistry and test requirements before you swap one for another.

For frame and chassis parts that must be both strong and formable, look at QStE or MC grades. They reach higher strength without the cracking you get from simply choosing a harder steel.

Thickness: What Hot Rolling Does Well

Hot rolled coil is most economical from about 2 mm to 12 mm. Below 1.5 mm, hot rolled gauge control gets harder, and cold rolled often makes more sense. Above about 20 mm, coils become heavy and hard to level, and plate is usually the better buy. For plate, see Carbon Steel Plate.

Black Surface or Pickled and Oiled

Mill scale is fine under hot-dip galvanizing, blasting and most welding. It is a problem for direct painting, powder coating and fine stamping, where scale flakes off.

For parts that go straight to a paint line, pickled and oiled coil usually costs less than pickling in-house. If the part is blasted or galvanized anyway, buy black and save the pickling charge.

Reading Hot Rolled Coil Prices

Hot rolled steel prices move with the market for iron ore, coke and scrap. Most buyers watch the HRC trend before they place a large order. On top of the base price, these factors change your quote:

  • Grade: structural and automotive grades cost more than commercial grades
  • Thickness: thin gauges under 2 mm cost more per ton
  • Width: very narrow or very wide coils cost extra
  • Surface: pickled and oiled costs more than black coil
  • Processing: slitting, leveling and recoiling add a service charge

Ask for the price per ton FOB or CFR, and check that the grade, standard and tolerance match your drawing. A lower price for a different standard is not a saving.

Matching Coil Weight to Your Plant

A 25- to 28-ton coil is efficient for a big slitting line but too heavy for many workshops. Smaller coils mean more coil changes, but no crane upgrade. We can split one mill coil into several smaller coils with the same heat and certificate.

Storage on Arrival

Black hot rolled coil handles storage well, but keep it dry to avoid heavy rust. Pickled coil has only a light oil film. Store it indoors and use it within a few months for the best paint adhesion.

Frequently Asked Questions


What is HRC?

HRC means hot rolled coil: steel rolled at high temperature into a thin, wide strip and wound into a coil. It is the base product for most flat steel. Buyers slit it, cut it into sheets, form it into pipe, or roll it further into cold rolled coil.

What is the difference between HRC and CRC?

HRC is rolled hot, so it carries mill scale and wider gauge tolerance at a lower price. CRC is rolled again at room temperature, so it is thinner, smoother and more precise. Choose HRC for structural and welded parts, and CRC for visible or deep-drawn parts.

What affects hot rolled coil price?

The HRC market sets the base, then grade, thickness, width, surface and processing add to it. Thin gauges and high-strength grades cost more per ton. For the current HR coil price per ton, send your specification and we will quote within 2–4 working hours.

Can you supply prime hot rolled steel coils from stock?

Yes. We supply prime coils only, and hold common grades and sizes in our own warehouses. Other grades and sizes are rolled to order in about 2–3 months.

What thickness of hot rolled coil can you supply?

Our standard range is 1.2–20 mm. We can supply 0.8–25.4 mm on request, but coils over 20 mm are rare, heavy and made to order. Above 20 mm, plate is usually the better form.

Do you supply hot rolled coil for wholesale buyers?

Yes. We sell full mill coils for re-rollers, service centers and distributors, as well as processed coils for end users. You can load mixed grades and sizes in one container.

Request a Quote


We reply within 2–4 working hours with a price per ton, valid for 3 days.

Scroll to Top

Envíe su consulta hoy

Envíenos el grado, la medida, la cantidad y el puerto de destino que necesita. Para productos estándar, le enviamos una cotización en 2–4 horas hábiles.

Send Your Inquiry Today

Send us your required grade, size, quantity and destination port. For standard products, we will provide a quote within 2–4 working hours.