Hot rolled steel coils in stock

S355MC Steel Coil (1.0976, EN 10149-2)

S355MC hot rolled coil for cold-formed frames, chassis parts and sections, with the full MC series from S315MC to S700MC. We slit and cut MC coil on our in-house processing lines, then ship it from our own warehouses.

Standard 2.0–8.0 mm thick; 1.5–20 mm on request

Standard widths 1000, 1250 and 1500 mm; 900–2000 mm on request

S315MC to S700MC, plus BS600MC to BS700MC

Mill test certificate to EN 10149-2; quotations in 2–4 working hours

Why Buy S355MC From MTS


Blanks and Strip From Our Own Lines

We cut MC steel sheets up to 16 mm thick and 2000 mm wide. For strip, we slit coil up to 14 mm thick, from 20 mm wide. High-strength steel is harder on knives, so we set each job by grade and thickness. You get blanks and strip ready for your brake or roll former.

One Supplier for the Whole MC Series

S355MC is the volume grade, but frame designs often mix strengths. We supply S315MC to S700MC and BS600MC to BS700MC on one quotation. Not every grade is available in every size, so we confirm the combination before you order.

Stock for Common Sizes

Common MC grades and sizes are part of our 9,000 tons of carbon steel coil stock. Other grades and sizes are rolled to order in about 2–3 months.

Coil Weight to Suit Your Plant

Standard hot rolled coils weigh 15–25 tons on a 760 mm ID. If your decoiler takes 610 mm or your crane lifts less, we rewind to match.

Shipped From Three Ports

Processed orders ship in 8–12 working days from Shanghai, Qingdao or Tianjin. Every container is photographed before it is sealed.

Hot rolled steel coils in stock

High Strength That Still Bends

S355MC belongs to EN 10149-2, the standard for thermomechanically rolled steel for cold forming. It reaches a 355 MPa minimum yield, the same as structural S355, but with low carbon and fine grain. That lets it bend tightly without cracking.

The result is lighter parts. A frame member in S355MC, or in a higher MC grade, can be thinner than one in S235 or S275. Less steel means less weight on the road and lower material cost per part.

Tell us what you form and which machine you use. You’ll get a recommended MC grade and thickness that meet your load without making the part hard to bend.

Request a Quote

MC Steel Grades


Hot rolled steel coils in stock

S315MC and S355MC

The most widely used MC grades. For trailer cross members, roll-formed profiles, brackets, racking and light chassis parts.

Hot rolled steel coils in stock

S420MC and S460MC

A step up in strength for crane parts, truck sub-frames and agricultural machinery. Thinner sections at the same load.

Hot rolled steel coils in stock

S500MC to S550MC

For weight-saving frame members and longitudinal beams where load and fatigue matter.

Hot rolled steel coils in stock

S600MC to S700MC

The highest-strength MC grades, for crane booms, telescopic arms and lightweight trailer chassis. On your press brake, they need closer control of bend radius.

Hot rolled steel coils in stock

BS600MC to BS700MC

High-strength cold-forming grades of Chinese origin, used for similar frame and boom parts. Choose them when your drawing or customer specifies them.

Example: S355MC hot rolled coil, 4.0 mm × 1500 mm, slit to 2 × 750 mm for trailer side rails.

S355MC Specifications


ItemStandardAvailable on request
Thickness2.0–8.0 mm1.5–20 mm
Width1000 / 1250 / 1500 mm900–2000 mm
Coil ID760 mm610 mm
Coil weight15–25 tmax. 28 t
SurfaceBlack, as rolledPickled and oiled for some grades and thicknesses
Thickness toleranceEN 10051—

Available sizes differ by grade. Sizes outside the standard column need confirmation with us, and some are made to order.

How to Choose and Order MC Steel

What “MC” Means

In EN 10149-2, “M” stands for thermomechanically rolled and “C” for suitability for cold forming. Thermomechanical rolling controls temperature and reduction to give a fine grain. Small additions of niobium, vanadium or titanium add strength without much carbon.

S355MC or S355JR?

Both have a 355 MPa minimum yield. S355JR (EN 10025-2) is a structural grade, made for welding and load, not tight bending. S355MC has lower carbon and finer grain, so it bends at a much smaller radius without cracking. If your part is press-braked or roll-formed, choose S355MC. If it is a flat welded plate, S355JR is usually enough.

Going Higher Than S355MC

Higher MC grades let you cut thickness and weight, but each step needs more bending force and a larger minimum radius. Before you switch from S355MC to S500MC or S700MC, check your press brake tonnage, tooling and spring-back allowance. A cheaper thinner part is no saving if your brake cannot form it.

Black or Pickled Coil

MC coil is normally supplied black, with mill scale. Some grades can be supplied pickled and oiled, depending on grade, thickness and strength level. If you need a clean surface for painting or powder coating, tell us the grade and size, and we will confirm. Otherwise, plan shot blasting after forming.

What to Check on the Certificate

Check the grade, the standard EN 10149-2, the yield and tensile results, and the elongation. For critical parts, confirm the bend test requirement on your order. Equivalent grades in other standards are close, not identical.

Frequently Asked Questions


What is S355MC steel?

S355MC is a hot rolled high-strength steel for cold forming, to EN 10149-2. It has a minimum yield strength of 355 MPa and low carbon, so it bends easily. It is used for chassis parts, trailer frames and cold-formed sections.

What does MC stand for in S355MC?

“M” means thermomechanically rolled, and “C” means suitable for cold forming. “S” is structural steel and 355 is the minimum yield strength in MPa.

What is 1.0976 material?

1.0976 is the European material number for S355MC under EN 10149-2. Drawings may show 1.0976 or S355MC; both refer to the same steel.

What is the S355MC material composition?

Maximum 0.12% carbon, 1.50% manganese, 0.50% silicon, 0.025% phosphorus and 0.020% sulfur, with micro-alloying by niobium, vanadium or titanium. Actual results are on each mill certificate.

What thickness of S355MC can you supply?

The standard range is 2.0–8.0 mm, 1000–1500 mm wide. We can supply 1.5–20 mm and 900–2000 mm wide on request. Sizes outside the standard range need confirmation with us.

Can you supply S700MC?

Yes. We supply S315MC to S700MC, plus BS600MC to BS700MC. Available sizes vary by grade, so send your thickness and width and we will confirm.

Request a Quote


We reply within 2–4 working hours with a price per ton, valid for 3 days.

Scroll to Top

Envíe su consulta hoy

Envíenos el grado, la medida, la cantidad y el puerto de destino que necesita. Para productos estándar, le enviamos una cotización en 2–4 horas hábiles.

Send Your Inquiry Today

Send us your required grade, size, quantity and destination port. For standard products, we will provide a quote within 2–4 working hours.