Cold rolled steel coils in the warehouse

DC01 Steel Coil and Sheet (1.0330)

DC01 cold rolled steel coil and sheet to EN 10130, with DC03, DC04 and DC05 for deeper drawing. We slit and cut DC01 on our in-house processing lines, then ship it from our own warehouses.

Coil 0.3–3.0 mm thick, standard widths 1000, 1250 and 1500 mm

Sheet 0.5–3.0 mm, in 1000 × 2000, 1219 × 2438, 1250 × 2500 and more

Annealed and skin passed, matte and oiled as standard

Mill test certificate to EN 10130; quotations in 2–4 working hours

Why Buy DC01 From MTS


Cut to Your Blank Size

We cut DC01 sheets from 300 mm to 2000 mm wide, flat to 5–7 mm per meter. For strip, we slit DC01 coil from 20 mm wide, with a width tolerance of ±0.2 mm. Your blanks arrive ready for pressing or laser cutting.

Coil or Sheet, Same Grade

Order DC01 as master coil, slit coil or flat sheet on one quotation. Coils weigh 5–10 tons on a 508 mm ID, with 610 mm also available. We can rewind thin gauges into smaller coils for your decoiler.

DC01 to DC05 in Stock

We stock DC01, DC03, DC04 and DC05 coil. You can move up a grade when you need a deeper draw, without waiting for a mill rolling slot. DC06 is made to order.

Certified to the EN Standard

Each coil is certified to EN 10130, with thickness tolerance to EN 10131. If your customer works to JIS or ASTM, we can supply SPCC or ASTM A1008 instead.

Shipped From Three Ports

Processed DC01 ships in 8–12 working days from Shanghai, Qingdao or Tianjin. Every container is photographed before it is sealed.

Cold rolled steel coils in the warehouse

DC01: Europe’s Standard Grade for Cold-Formed Parts

DC01 is the commercial quality grade in EN 10130, the European standard for cold rolled low carbon steel for cold forming. Its material number is 1.0330, and it replaced the old German grade St12.

DC01 bends, folds and presses well, and welds easily. It is the first choice for cabinets, brackets, panels, furniture and light pressed parts. It is not a structural grade, so it carries no guaranteed minimum yield strength.

When the draw gets deeper, the same standard steps up to DC03, DC04 and DC05. Each step has lower carbon and higher elongation. Tell us how your part is formed, and we will confirm which DC grade fits.

Request a Quote

DC01 to DC05 Cold Rolled Steel


Cold rolled steel coils in the warehouse

DC01 (1.0330) – Commercial Quality

For bending, folding, roll forming and shallow pressing. The lowest-cost DC grade and the most widely stocked.

Cold rolled steel coils in the warehouse

DC03 (1.0347) – Drawing Quality

For moderate draws where DC01 starts to split or neck. A common step up for housings and deeper brackets.

Cold rolled steel coils in the warehouse

DC04 (1.0338) – Deep Drawing Quality

For deep-drawn automotive and appliance parts. Close to the old St14 grade.

Cold rolled steel coils in the warehouse

DC05 (1.0312) – Special Deep Drawing Quality

For deep and complex shapes, with very low carbon and high elongation.

DC01 by Form


DC01 Cold Rolled Coil

Full-width coil for press lines, roll formers and service centers. Standard 0.3–3.0 mm thick and 1000–1500 mm wide.

DC01 Steel Sheet

Flat sheets cut from coil, 0.5–3.0 mm thick. Standard sizes include 1000 × 2000, 1219 × 2438, 1250 × 2500 and 1500 × 3000 mm.

DC01 Slit Strip

Narrow coils from 20 mm wide for tube mills, profiles and progressive dies.

Example: DC01 AM cold rolled sheet, 1.0 mm × 1250 × 2500 mm, for electrical cabinet panels.

DC01 Specifications


ItemCoilSheet
Thickness, standard0.3–3.0 mm0.5–3.0 mm
Thickness, on request0.2–4.0 mm0.2–4.0 mm
Width, standard1000 / 1250 / 1500 mm1000 / 1219 / 1250 / 1500 mm
Width, on request700–1850 mm700–1850 mm
Length—2000 / 2438 / 2500 / 3000 mm; 1000–6000 mm on request
Coil ID / weight508 mm (610 mm); 5–10 t (3–15 t)—
Thickness toleranceEN 10131EN 10131

Sizes outside the standard range need confirmation with us, and some are made to order.

How to Specify DC01 Correctly

Reading a Full DC01 Designation

A complete order reads like “EN 10130 DC01-A-m”. DC01 is the grade. “A” is surface quality: small defects are allowed that do not affect forming or coating. “B” means the better side is free of defects that would show under paint. “m” is a matte finish; “b” is bright. On orders, this is often shortened to DC01AM.

If your part is a visible, painted panel, ask for surface B. For hidden parts and powder-coated cabinets, A is the usual and cheaper choice.

DC01, DC03 or DC04?

Start with DC01 for bending and shallow pressing. If the press shows splits, necking or orange peel at the corners, the draw is too deep for commercial quality. DC03 adds formability; DC04 handles most deep-drawn parts. Do not buy DC04 by default; you pay for formability you may not use.

DC01 Is Not S235

DC01 and S235JR are often confused because both are low carbon. S235JR is a structural grade with a guaranteed minimum yield of 235 MPa. DC01 has only a maximum yield, because softness is what forming needs. If your drawing asks for a load-bearing part, DC01 is the wrong grade.

DC01 or DD11?

DD11 is the hot rolled forming grade in EN 10111, roughly the hot rolled partner of DC01. It is cheaper from about 1.5 mm up. Choose DC01 when you need a smooth surface, tight tolerance or gauges under 1.5 mm.

What C490, C590 and C690 Mean

We can supply DC01 narrow strip to EN 10139 in cold rolled tempers, such as DC01+C490 or DC01+C590. The number is the minimum tensile strength in MPa. These tempers give a harder, springier strip than annealed DC01. We confirm the exact temper and properties against the standard before you order.

EN 10130, EN 10131 and EN 10139

EN 10130 sets the grades and properties of cold rolled sheet and coil. EN 10131 sets thickness, width and flatness tolerances. EN 10139 covers cold rolled narrow strip, including the hard tempers. A clear purchase order names the grade standard and the tolerance standard together.

Frequently Asked Questions


What is DC01 steel?

DC01 is a cold rolled low carbon steel grade in EN 10130. It is the commercial quality grade for bending, folding and light pressing. Its material number is 1.0330, and it replaced the old German St12.

What is material 1.0330?

1.0330 is the European material number for DC01 cold rolled steel. Drawings may show 1.0330, DIN 1.0330 or DC01; they all refer to the same grade under EN 10130.

What is the equivalent of DC01?

The closest equivalents are St12 (old DIN 1623), SPCC (JIS G3141) and CR4 (old BS 1449). ASTM A1008 commercial steel is used for similar parts in the US. They are close, not identical.

What is the difference between DC01, DC03 and DC04?

They are commercial, drawing and deep drawing quality in EN 10130. Carbon falls and elongation rises from DC01 to DC04. Choose by how deep your part is drawn.

What does DC01AM mean?

DC01AM is DC01 with surface quality A and a matte (m) finish. It is the most common way DC01 is ordered for general pressing and painted parts.

What thickness of DC01 can you supply?

DC01 coil is standard 0.3–3.0 mm and sheet 0.5–3.0 mm. We can supply 0.2–4.0 mm on request; sizes outside the standard range need confirmation with us.

Request a Quote


We reply within 2–4 working hours with a price per ton, valid for 3 days.

Scroll to Top

Envíe su consulta hoy

Envíenos el grado, la medida, la cantidad y el puerto de destino que necesita. Para productos estándar, le enviamos una cotización en 2–4 horas hábiles.

Send Your Inquiry Today

Send us your required grade, size, quantity and destination port. For standard products, we will provide a quote within 2–4 working hours.