Home

/

/

High Carbon Steel Coil

Hot rolled steel coils in stock

SK85 High Carbon Steel Coil

Hot rolled high carbon and spring steel coil in SK85 (SK5), SK95 and manganese spring steel, for springs, blades, saws and tools. We slit coil to your width on our in-house processing lines, then ship it from our own warehouses.

Manganese spring steel coil, standard 2.5–10.0 mm thick and 1250 mm wide

SK85 and SK95 hot rolled coil, standard 2.0–4.0 mm, 1000 or 1250 mm wide

Slit to your strip width; cold rolled SK85 and spring steel strip on request

Mill test certificate with every coil; quotations in 2–4 working hours

Why Buy High Carbon Steel Coil From MTS


Slit for Your Blanking and Re-Rolling

High carbon steel is hard on slitting knives, so width accuracy depends on setup. We slit high carbon coil into strip from 20 mm, with a width tolerance of ±0.2 mm. Your strip arrives ready for blanking, re-rolling or heat treatment.

The Grades Spring and Blade Makers Use

Manganese spring steel is the workhorse spring grade; SK85 and SK95 are the classic blade and tool grades. You can buy all three on one quotation, plus precision cold rolled spring strip.

Stock for Common Sizes

We stock SK85 and manganese spring steel coil in common sizes. Other sizes are rolled to order in about 2–3 months.

Hardness to Your Requirement

Quenched and tempered strip and specific hardness ranges are available on request. Tell us the hardness and the parts you make, and we will advise on supply condition.

Shipped From Three Ports

Processed orders ship in 8–12 working days from Shanghai, Qingdao or Tianjin.

Hot rolled steel coils in stock

Carbon That Makes the Steel Spring Back

High carbon steel contains roughly 0.6% to 1.0% carbon, several times more than mild steel. After hardening and tempering, it becomes hard, wear resistant and elastic. That is why springs return to shape and blades hold an edge.

The trade-off is formability. High carbon steel is harder to bend and weld than low carbon steel, and its properties depend on correct heat treatment. Choosing the grade and supply condition early saves trouble at the press and in the furnace.

Tell us what you make, how you form it, and the final hardness. You’ll get a recommended grade, thickness and condition.

Request a Quote

High Carbon Steel Grades


Hot rolled steel coils in stock

Manganese Spring Steel Coil (1065 Class)

A manganese spring steel to GB/T standards, with about 0.65% carbon. Used for flat springs, clips, washers, agricultural blades and saw blanks. Standard 2.5–10.0 mm thick, with 1.5–12.7 mm available; 1250 mm wide, 900–1600 mm on request.

Hot rolled steel coils in stock

SK85 (SK5) Carbon Tool Steel Coil

SK85 is the JIS G4401 grade formerly called SK5, with about 0.85% carbon. Used for knives, saw blades, cutters and springs. Standard 2.0–4.0 mm thick, with 1.5–6.0 mm available; 1000 or 1250 mm wide.

Hot rolled steel coils in stock

SK95 High Carbon Steel Coil

About 0.95% carbon, for parts that need maximum hardness and edge retention. Same size range as SK85.

Bright cold rolled precision spring steel strip coils

C67S and C75S Precision Spring Strip

Cold rolled spring steel strip, standard 0.5–1.5 mm thick, for precision springs and clips.

Example: Manganese spring steel hot rolled coil, 3.0 mm × 1250 mm, slit to 60 mm strip for agricultural blades.

High Carbon Steel Coil Specifications


GradeThickness, standardThickness, on requestWidth, standardWidth, on request
65Mn (hot rolled)2.5–10.0 mm1.5–12.7 mm1250 mm900–1600 mm
SK85 / SK5, SK95 (hot rolled)2.0–4.0 mm1.5–6.0 mm1000 / 1250 mm900–1600 mm
C67S, C75S (cold rolled strip)0.5–1.5 mmconfirm with usslit to order—
65Mn, SK85 (cold rolled strip)on request—slit to order—

Sizes outside the standard columns need confirmation with us, and some are made to order.

How to Choose High Carbon Steel Coil

Manganese Spring Steel or SK85?

Manganese spring steel has less carbon and more manganese. It hardens deeply and keeps good toughness, so it suits springs, washers and blades that flex. SK85 has more carbon, so it reaches higher hardness and holds an edge better. Choose it for knives, saw blades and cutting parts. If the part must flex and cut, discuss the balance with us before ordering.

Hot Rolled Coil or Cold Rolled Strip?

Hot rolled high carbon coil is the lower-cost starting point for thicker parts and for re-rollers. Below about 1.5 mm, or when thickness tolerance and surface matter, cold rolled spring strip is the better buy. C67S and C75S are made for that precision work.

Supply Condition and Heat Treatment

Hot rolled high carbon steel is hard to blank and bend tightly. Many makers blank or form first, then harden and temper the finished part. Others buy strip already quenched and tempered to a set hardness. Tell us which route your plant uses; it changes what you should order.

Why Decarburization and Surface Matter

Hot rolling leaves a thin layer at the surface with less carbon. That layer stays softer after hardening. For blades and fatigue-loaded springs, ask about surface condition and allow for grinding or removal where needed.

Storage and Handling

High carbon coil rusts like any carbon steel. Store it dry, and keep slit coils banded until use. Avoid sharp bends in handling; hard strip can crack at kinks.

Frequently Asked Questions


What is SK85 steel?

SK85 is a high carbon tool steel grade in JIS G4401, with about 0.85% carbon. It was formerly called SK5. It is used for knives, saw blades, cutters and springs.

Is SK85 the same as SK5?

Yes. SK5 is the old JIS name. The 2006 revision of JIS G4401 renamed it SK85, after its carbon content. Many buyers still order it as SK5.

What is 65Mn steel?

65Mn is the Chinese name for a manganese spring steel with about 0.65% carbon and 0.9–1.2% manganese. It is close to SAE 1065 / 1566. Buyers use it for flat springs, clips, washers and agricultural blades.

What thickness of spring steel coil can you supply?

Manganese spring steel coil is standard 2.5–10.0 mm, 1250 mm wide. We can supply 1.5–12.7 mm and 900–1600 mm wide on request.

Can you supply spring steel coil in cold rolled strip?

Yes. C67S and C75S precision spring strip is standard 0.5–1.5 mm. We quote cold rolled SK85 and manganese spring steel strip on request.

Can you supply hardened and tempered strip?

Yes, on request. Send the grade, thickness, width and target hardness, and we will confirm.

Request a Quote


We reply within 2–4 working hours with a price per ton, valid for 3 days.

Scroll to Top

Envíe su consulta hoy

Envíenos el grado, la medida, la cantidad y el puerto de destino que necesita. Para productos estándar, le enviamos una cotización en 2–4 horas hábiles.

Send Your Inquiry Today

Send us your required grade, size, quantity and destination port. For standard products, we will provide a quote within 2–4 working hours.